Whatsapp: +86 156-7062-6070

INTRODUCTION

    Peat rotary dryer is special design for peat of high moisture, big viscosity, small density, low heat resistance, easy cluster, and other character development and market demand product. This peat drying system main included heating source, Break feed equipment, Belt feeding machine, rotary drum, discharge equipment, dust removal, belt discharging machine, induced draft fan, peat combustion, temperature control, power operation system and system structure.

   The Peat Coal Dryer uses a special dispersing device to break up the bonded slime and dry it. The contact area between the slime and the hot air is increased, and the heat utilization rate is greatly improved. The dried slime can reduce the moisture to less than 12% at one time, and the dried coal slime can be directly used as a fuel, which makes the coal slime into treasure.

   This type of equipment can be used for drying all kinds of coal, lignite, carbon coal, including anthracite, lean coal and poor lean coal, lean coal, coking coal, fat coal, air fertilizer coal, gas coal, coal, and weakly caking coal, not sticky coal, long flame coal, lignite, coal washing, screening, raw coal, bituminous coal, the tail coal, midding coal, etc. Equipment can be made according to the customers' requirements.

Peat Dryer
Peat Dryer
Peat Dryer

PRINCIPLE

Whatsapp: +86 156-7062-6070

The working principle of the dryer system as follows: 

1. First is moisture content 35-60% peat by scattered feeder evenly into the dryer, in the process of drying, peat will pass six workspace: one is the feed zone, wet peat into this area with low temperature hot air quickly evaporate moisture, the material in big Angle of copy board copy, In front of the binder will import to next workspace.

2. Second is repeatedly broken beat and cleaning area, equipment design in this area have broken beat cleaning device, wet peat grabbed by grating copy board broken beat, large wet slurry after repeated broken beat, broken knead into a 20-30 mm small particles of carbon, forming curtain material status, increase the heat exchange area, improve the drying rate, cleaning device reasonably clean wall adhesion of peat, prevent peat adhesive.

3. Three is the main drying area, through two area processing wet peat has a granular loose state of the material, in this area will be raising by inclined feed plate, the material will form a uniform state of material desire, and full contact with hot air to heat exchange, strong precipitation.

4. Four is pounding broken drying area, in this area peat after repeated pounding broken in this area, peat particles from 20-- 30 mm broken for 3-15mm size (as customer request), further reducing moisture content.

5. Five is strengthening drying region, through the broken small peat particles from the copy board raised area is densely populated, fully absorb hot heat, discharging water, achieved water standard, ready to discharge;

6. Six is discharging area, to prevent discharging dust, do not set copy plate roller in this region, the slide material rolling to the discharge port to complete the whole drying process. Peat moisture content is  10-15%, 3-15 mm granular coal or organic fertilizer. 

PARAMETERS

Model Capacity(T/D) Initial moisture(%) Final moisture(%) Total Power(kw) Covering area(m²)
DLMG1916 300 ≤30 13±2 130 42*16
DLMG2220 500 ≤30 13±2 150 46*16
DLMG2522 800 ≤30 13±2 200 48*16
DLMG2825 1000 ≤30 13±2 250 51*16
DLMG3026 1300 ≤30 13±2 280 52*18
DLMG3228 1500 ≤30 13±2 330 55*18
DLMG3430 1800 ≤30 13±2 380 56*18
DLMG3632 2200 ≤30 13±2 450 58*18
DLMG3835 2700 ≤30 13±2 560 60*18
DLMG4036 3000 ≤30 13±2 660 60*18

LEAVE US A MESSAGE.

we will give you customized Proposal & Quotation within 24 hour

LEAVE US A MESSAGE

Welcome to discuss your project requirements, We will give you customized Proposal & Quotation within 24 hours.